WPI Chemical Hygiene Plan

Issued: January, 1992
Revised: March, 1993
Revised: April, 1995
Revised: December, 1999
Revised: May, 2000
Revised: July 2004

The principal focus of the WPI Chemical Hygiene Plan (CHP) is that of a written plan capable of protecting laboratory workers from health hazards associated with hazardous chemicals, and keeping exposures below the Permissible Exposure Levels (PEL), as published and enforced by OSHA as a legal standard. It is designed to be a working document, readily available to all employees. The CHP shall include each of the following elements and shall indicate specific measures that WPI will take to ensure laboratory employee protection:

Standard Operating Procedures for the use of hazardous chemicals.
Criteria for determining and implementing control measures to reduce exposure.
Measures to assure proper functioning of fume hoods and other engineering controls.
Provisions for employee information and training.
Circumstances under which a laboratory operation or procedure will require prior approval.
Provisions for medical consultation and examination.
Designation of responsible personnel, including the Chemical Hygiene Officer.
Provisions for particularly hazardous substances.

This CHP is generic to all WPI Laboratories. It is to be used as a starting point of lab safety information. It is the responsibility of the lab supervisor to add specific safety information for his/her laboratory operations and experiments which are not covered by this plan.

1. Standard Operating Procedures

1.A. General Rules

Awareness is the most fundamental rule of chemical safety. Everyone working in a laboratory should remain constantly aware of:

The chemicals hazards, as determined from the Material Safety Data Sheet (MSDS) and other appropriate references. MSDS's may be electronically retrieved from WPI's Safety Homepage.
Appropriate safeguards for using that chemical, including personal protective equipment.
Location and proper use of emergency equipment.
How to properly store the chemical when not in use.
Proper personal hygiene practices.
The proper use, maintenance, and limitations of personal protective equipment.
The proper methods of transporting chemicals within the facility.
Appropriate procedures for emergencies.

Never put yourself at greater risk by working alone in a laboratory. Working alone is not allowed.

1.B. Personal Hygiene

Personal hygiene is an important factor in chemical hygiene. To affect a person, a toxic chemical must contact that person. The four routes of entry (inhalation, ingestion, injection, and eye and skin contact) limit the chemical's ability to contact us. If we properly protect ourselves, we can eliminate the chemical's ability to do harm. Some good personal hygiene practices include:

Wash promptly if skin contact is made with any chemical.
Wear appropriate eye protection at all times.
Avoid inhalation of chemicals; do not "sniff" test chemicals.
Do not mouth pipette anything; use suction bulbs.
Wash well before leaving the laboratory; do not wash with solvents; use soap.
Change clothing as soon as possible after leaving the laboratory, and launder work clothes often.
Do not drink, eat, smoke, or apply cosmetics in the laboratory.

1.C. Food and Smoking

There should be no eating, drinking, smoking, or application of cosmetics allowed in areas where chemicals are either stored or used. Because chemical vapors can be absorbed by foodstuff and tobacco, no food or tobacco products should be allowed into chemical use areas.

1.D. Personal Protective Equipment (PPE)

The most fundamental piece of protective equipment is the clothing, which a lab worker wears. Clothing should be worn to minimize exposed skin surfaces available for direct contact through splashing. Therefore, all lab workers should wear long sleeved/long legged clothing and avoid short sleeved shirts, short trousers or skirts. Sandals, open-toed shoes and canvas shoes should not be worn in the laboratory.

In addition, the following is a list of PPE which is the responsibility of the laboratory worker to make certain is appropriate protection for the hazards encountered:

Eye Protection
Respirators
Gloves
Aprons
Face Shields
Lab Coats

A detailed review of PPE is found in section 2.E.

1.E. Housekeeping

Common housekeeping practices contribute to improving chemical hygiene and safety. A clean, organized work area is much safer than a cluttered or dirty one. Some appropriate housekeeping measures include:

Keep all aisles, hallways, and stairs clear of all chemicals.
Keep all work areas, especially lab benches, clear of clutter and obstruction.
All working surfaces and floors should be cleaned regularly.
Wastes should be kept in the proper containers and labeled properly.
Access to emergency equipment, showers, eyewashes and exits, should never be blocked by anything.
Never store chemicals on the floor, even temporarily.
Laboratory staff should be considerate and aware of the housekeeping staff. The typical housekeeping staff is not as highly educated on chemicals and their hazards as most laboratory workers.
Therefore, for the safety of housekeeping staff, laboratory workers should make sure that:
All broken glassware is safely disposed of. Do not throw broken glass in the trash unless it is enclosed in a solid secondary container.
All chemicals are placed in proper storage areas by the end of each workday.
All chemical containers are labeled with both the identity of the chemical and its hazards.
All spills are promptly cleaned up and the spilled chemical is properly disposed of.

1.F. When Not to Proceed with Experimental Work in a Laboratory

Sometimes, laboratory workers should not proceed with what seems to be a routine task. Under some conditions, the routine task might contain hazards not fully recognized by the worker. Workers should recognize certain indicators to review the procedure, including but not limited to:

New procedure, process or test even if it is very similar to older practices.
It is likely that toxic limit concentrations could be exceeded or that other harm is likely.
Change or substitution of any of the ingredient chemicals in a procedure.
Failure of any of the equipment used in the process, especially safeguards such as fume hoods or clamp apparatus.
Unexpected test results. When a test result is different than predicted, a review of how the new result impacts safety practices must be made.
If members of the laboratory staff become ill, suspect exposure, or otherwise suspect a failure of laboratory safeguards.
The occurrence of any of these conditions should result in work stoppage and immediate investigation by the laboratory supervisor.
The results of the investigation should be reported immediately to the Chemical Hygiene Officer (CHO) who must decide whether to continue the investigation, institute any additional corrective actions beyond those of the laboratory supervisor, or allow work to continue.

1.G. Spills and Accidents

Spills of toxic substances or accidents involving any hazardous chemicals should be resolved immediately. The overall steps to handle a spill or accident are:

Notify your supervisor or other nearby laboratory workers, and the appropriate emergency responders immediately. Call Campus Police at x5555.
If the spilled chemical is flammable, extinguish all nearby sources of ignition.
If a person has been splashed with a chemical, wash the victim with plenty of water for at least 15 minutes, remove all contaminated clothing, and get medical attention.
If a person has been overexposed by inhalation, get the victim to fresh air, and get medical attention.
After securing proper medical attention for a chemical exposure victim, neutralize or absorb the spilled chemical with the proper spill clean up material and dispose of it in accordance with the WPI hazardous waste policy.
For assistance with chemical spills, call the Environmental and Occupational Safety Office, x 5216.

There are some fundamental actions which must NOT be used in handling emergencies. Some of them include:

DO NOT handle emergencies alone, especially without notifying someone that the accident has occurred.
DO NOT apply medical aid procedures without some training in that area.
DO NOT linger at the accident scene if you are not one of the emergency responders.

1.H. Waste Chemicals

Chemical wastes are regulated by the Environmental Protection Agency (EPA) under the Resource Conservation and Recovery Act (RECRA) as well as the Commonwealth of Massachusetts. Hazardous Waste Regulations, 310 CMR 30.000. WPI has its own Hazardous Waste Policy, based upon these regulations.

Each laboratory worker at WPI should have a copy of the Hazardous Waste Policy, and be familiar with its procedures. It is the responsibility of every laboratory worker, faculty, staff and student to legally and safely dispose of all hazardous chemical wastes. For a copy of the WPI policy, contact the Chemical Hygiene Officer, Dave Messier, x5216, or retrieve it from WPI's Safety Homepage.

1.I. Procedure-Specific Safety Procedures

Written laboratory procedures normally have a brief description of specific safety practices for that particular procedure. Lab workers should read and review those practices before commencing a procedure.

2. Criteria to Determine and Implement Control Measures to Reduce Exposure to Hazardous Chemicals

Chemical safety is accomplished by awareness of a chemical's hazards, and by keeping the chemical under control through a variety of engineered safeguards. Laboratory workers should be familiar with the proper use of those safeguards. Laboratory supervisors should be able to detect the malfunction of those safeguards. All engineered controls must be properly maintained, inspected on a regular basis, and never overloaded beyond their design limits.

2.A. General Ventilation

General ventilation refers to the quantity and quality of the air supplied to the laboratory. The building ventilation system should ensure that the laboratory air is continuously being replaced so that harmful concentrations of hazardous chemicals do not increase during the working day.

2.B. Fume Hoods

The fume hood is the best local exhaust device used in laboratories. It is, however, but one part of the total ventilation system and should not be considered as separate from the total system, because its performance will be strongly influenced by other features in the general ventilation system. All work done with chemicals with low exposure limits or high vapor pressures should be done in a fume hood. To ensure your fume hood provides the highest degree of protection, observe the following guidelines:

Only materials being used in an ongoing experiment should be kept in the fume hood. Cluttering of the hood will create airflow disturbances.
Large apparatus inside a hood should be placed upon blocks or legs to allow air to flow underneath.
Operate the hood with the door as low as practical, but not above 15 inches open to insure worker protection.
Work as far into the hood as possible. At least six inches is recommended.
Keep your head outside the hood.
Avoid cross drafts at the face of the hood. Even pedestrian traffic may be sufficient current to cause air turbulence.
Keep hood door closed when not attended.

The performance standard for fume hoods at WPI is the delivery of a minimum face velocity of 75-100 linear feet per minute with a door opening of 15 inches. Performance testing is conducted by the Department of Plant Services, Environmental and Occupational Safety Office, on an annual basis.

2.C. Flammable Storage Cabinets

Cabinets designed for the safe storage of flammable chemicals can only do so if used and maintained properly. Always read the manufacturer's information, and abide by the following:

Store only compatible materials inside the cabinet.
Do not store paper or cardboard inside cabinets with the chemicals.
Do not overload the cabinet.

2.D. Eyewashes and Safety Showers

Eyewashes and safety showers will be provided wherever chemicals are handled for immediate first aid treatment of chemical splashes, and for extinguishing clothing fires.

Every laboratory worker should learn the locations of, and how to use the safety showers and eye washes in their laboratory so that he or she can find them with their eyes closed, if necessary.
Keep all passageways to the eyewash and shower clear of any obstacle (even temporary ones).
Showers should be tested annually to assure that access is not restricted, the start chain is within reach, and it functions properly.
Eye wash units should be flushed weekly by the lab workers.

2.E. Personal Protective Equipment (PPE)

A variety of specialized clothing and equipment is commercially available for use in the laboratory. The proper use of these items will minimize or eliminate exposure to the hazards associated with many laboratory operations. Every laboratory worker should be familiar with the location and proper use of the PPE in their laboratory area.

A brief introduction to PPE was made in section 1.D. Some additional information is found in appendix A, as well as in the following:

2.E.1. General Eye Protection Policy

Eye protection is required of all personnel and any visitors present in any location where chemicals are stored or handled. This protection should meet the requirements of the American National Standards Institute (ANSI) Z87.1. No one should enter any laboratory without appropriate eye protection. Safety spectacles that meet the criteria described below provide minimum eye protection for regular use. Additional protection may be required when carrying out more hazardous operations.

Contact lenses should not be worn in a laboratory. Gases and vapors can be concentrated under such lenses and cause permanent eye damage. Furthermore, in the event of a chemical splash in the eye, it is often nearly impossible to remove the contact lens to irrigate the eye because of involuntary spasm of the eyelid. There are some exceptional situations in which contact lenses must be worn for therapeutic reasons. Persons who must wear contact lenses should inform the laboratory supervisor so that satisfactory safety precautions can be devised.

2.E.2. Safety Glasses

Ordinary prescription glasses do not provide adequate protection from injury to the eyes. Safety glasses must be worn to protect the eyes from the impact of flying objects, and some extent chemical splashes. When safety glasses are worn without sideshields, liquid splashes or flying particles can potentially reach the eye. If sideshields are attached to the frames, greater protection against liquid or solid agents is afforded.

2.E.3. Goggles

Goggles provide greater protection against chemical splashes than safety glasses with sideshields due to the fact that they fit more closely to the face and form a more effective barrier against foreign materials. Goggles are also impact-resistant.

2.E.4. Goggles with Faceshield

Faceshields provide good protection to the eyes, face and neck against flying particles, sprays of hazardous liquids, splashes of molten metal and hot solutions. They are not recommended for eye protection against the impact of hurtling objects, therefore it is generally necessary to wear safety glasses or goggles underneath the faceshield.

2.E.5. Specialized Eye Protection

There are specific goggles and masks for protection against laser hazards, and other intense light sources, as well as glass blowing goggles, and welding masks and goggles. The laboratory supervisor should determine whether the task being performed requires specialized eye protection and require the use of such equipment if it is necessary.

2.E.6. Gloves

Proper protective gloves should be worn whenever the potential for contact with corrosive or toxic materials and materials of unknown toxicity exists. Gloves should be selected on the basis of the material being handled, the particular hazard involved, and their suitability for the operation being conducted. For technical assistance in proper glove selection, please refer to Appendix A, or call the Environmental and Occupational Safety Office at x5216.

2.E.7. Laboratory Clothing

The clothing worn by a laboratory worker can be important to their safety.

Such workers should not wear loose (neckties), skimpy (shorts), or torn clothing and unrestrained longhair.
Loose or torn clothing and unrestrained long hair can easily catch fire, dip into chemicals, or become ensnarled in moving laboratory equipment; skimpy clothing offers little protection to the skin in the event of a chemical splash.
Perforated shoes, sandals, or cloth sneakers should not be worn in laboratories or where mechanical work is being done.
Lab coats are intended to prevent contact via a chemical splash or a spill. The cloth lab coat is, however, primarily a protection for clothing, and may itself present a hazard (combustibility) to the wearer.
Lab coats should only be worn inside the laboratory to avoid the possibility of contamination outside the lab confines.
Rubber Aprons provide better protection from corrosive or irritating liquids in the event of a splash or spill.

2.E.8. Respirators

Suitable respiratory equipment shall be provided to all laboratory workers when engineering controls cannot maintain laboratory contaminants below acceptable levels.

The written respirator program, as mandated by 29CFR1910.134, will discuss issues such as respirator selection criteria, inspection, and maintenance.
All laboratory workers using respirators will be trained in there proper use and care.

2.E.9. Hearing Protection

Hearing protection should be worn in "high noise" areas to protect individuals from "noise-induced hearing loss", a permanent decrease in the ability to hear resulting from excessive exposure to noise. Different hearing protection devices vary in their ability to reduce noise. Hearing protectors include a variety of earplugs and earmuffs. Additional information on hearing protection can be found in Appendix A.

2.F. Vapor Detection

Do not use odor as a means of determining that inhalation limits are or are not being exceeded. Whenever there is reason to suspect that a toxic chemical inhalation limit might be exceeded, whether or not a suspicious odor is noticed, notify your supervisor. Laboratory workers should wear a respirator suitable for protection against the suspect chemical until measurements of the concentration of the suspect vapor in the air show that the limit is not exceeded. Under this circumstance, and if there is not reason to anticipate an increase in the concentration of the chemical, and if the supervisor approves, the respirator can be removed and the work may continue.

2.G. Criteria for Control Measures

This section examines the criteria and guidelines which will be used to determine the use of engineered and administrative controls and personal protective equipment.

2.G.1. Exposure Guidelines for Toxic Chemicals

The Material Safety Data Sheet (MSDS's) for many of the chemicals used in the laboratory will state recommended limits or OSHA-mandated limits, or both, as guidelines for exposure. Typical limits are threshold limit values (TLV), permissible exposure limits (PEL) and action levels. When such limits are stated, they will be used to assist the laboratory supervisor and/or chemical hygiene officer in determining the safety precautions, control measures and safety apparel that apply when working with toxic chemicals.

2.G.2. Flammability Guidelines

The flash point of a substance is the lowest temperature at which a liquid gives off vapor in sufficient concentration to form an ignitable mixture with air near the surface of the liquid. At WPI, the flash point of a chemical will be used as the reference standard for flammability.

OSHA and NFPA have guidelines on when a chemical is considered flammable. Those guidelines are herein adopted for use in the laboratory.
"Flammable" is generally used to refer to chemicals with a flash point below 100 degrees F.
"Combustible" is generally used to refer to chemicals with a flash point between 100 and 200 degrees F.
Any chemical with a flash point below 200 degrees F will be considered a fire hazard.

2.G.3. Reactivity Guidelines

Guidelines on which chemicals are reactive can be found in regulations from the Department of Transportation (49CFR) and the Environmental Protection Agency (40CFR). The NFPA has also developed guidelines on what constitutes a reactive chemical. All three of these sources will be used as a guideline to determine which substances are considered reactive.

At WPI, a reactive chemical is one which is:

Described as such on the chemical's MSDS.
Ranked by the NFPA as a 3 or 4 for reactivity.
Determined by the US DOT as either an oxidizer, an organic peroxide, or an explosive (Classes A, B, or C).
Fits the US EPA definition of reactive in 40CFR261.
Fits the OSHA definitions of unstable.
Is found to be reactive with ordinary substances.

Once a chemical has been determined to be reactive, all proper safety precautions will be used including extra segregation in storage and prohibition of mixing with other chemicals without personal protection and precautions.

2.G.4. Corrosive Material Guidelines

A corrosive chemical is defined by OSHA, DOT and EPA. WPI will consider a chemical corrosive if it fits the definition of corrosive in the following list of regulations.

OSHA 29 CFR
DOT 49 CFR
EPA 40 CFR
Corrosive materials are also designated as such on container labels and MSDS's.
Handle corrosive chemicals with all proper safety precautions, including wearing both safety goggles and face shield, gloves known to be resistant to permeation or penetration, and a laboratory apron or laboratory coat.

2.G.5. Miscellaneous Criteria for Control Measures

In addition to the previously listed guidelines in this section, WPI will use the available information on a chemical's Material Safety Data Sheet (MSDS) or on the container label. Appropriate control measures found on the label or product MSDS may contain the following information: health hazards, fire hazards, PPE required, storage and handling data, and disposal information. This information will be used to determine the appropriate control measures which are necessary to protect the health of all laboratory workers at WPI.

3. Measures to Assure Proper Functioning of Fume Hoods and Other Engineering Controls

Fume Hoods Program

The purpose of the Fume Hood Program at WPI is to assure that the hoods on campus perform adequately. The program includes a review of the installation plans of new fume hoods, regular inspections, preventative maintenance, education, and training.

3.A. Hood Requirements

WPI requires all fume hoods to maintain an average linear face velocity of 75-100 LFM at a sash height of at least 15 inches.
All fume hoods should be ducted and should have the fan located on the roof.
A make-up air system should be provided for all new hoods.
All new stacks should extend at least 6 feet above the roof line for optimum flow efficiency.
No hood should be used for a function for which it was not designed.

3.B. Hood Inspections

The Environmental and Occupational Safety Office schedules and performs annual inspections of all fume hoods on campus. Inspections include:

Air flow survey. This involves measurement of the face velocity with an air velocity meter. The current meter is a hot-wire anemometer, TSI Model 8350.
Check to verify if hoods are being used improperly.
Note any conditions which may cause obstruction in air flow or cross drafts.

All information is documented on a test report sheet. Information on this sheet includes the actual measurements and the hood's average face velocity, the date of inspection, the name of the individual performing the test, and a comment section for miscellaneous information such as messy conditions, excessive chemical storage or other unsafe practices which may be noted at the time of the inspection. A white certification sticker is dated and signed along with the LFM reading and placed on the left side of the fume hood cabinet.

If a hood does not meet the minimum face velocity of 75-100 LFM, the person testing the hood will make adjustments to the cabinet, if possible. This involves adjusting the baffle or damper, moving large objects which may be obstructing air flow, or any other adjustments which may improve the hood's performance.
If cabinet adjustments are not adequate, the inspector will initiate a Plant Services Work Order to correct the deficiency or repair the fume hood as needed.
A follow-up survey will be conducted once the Plant Services Department notifies the Environmental and Occupational Safety Office of any and all repairs to the equipment. The same inspection procedure as described above will occur.
During this process, the supervisor of the laboratory as well as the department head will be informed of this activity. The hood is not to be used during this time.
If the hood performance is still below standard after repairs have been made, Plant Services will be requested to make further adjustments.
A hood which fails to meet the 75-100 LFM will be labeled as not being suitable to work with hazardous materials.

3.C. New Hoods

The design plans of all new fume hoods at Worcester Polytechnic Institute will be reviewed prior to approval by the Environmental and Occupational Safety Office. In addition, the Environmental and Occupational Safety Office may evaluate the selection and design of all fume hoods before they are installed.
All newly installed fume hoods are reported to the Environmental and Occupational Safety Office and must be certified before they may be used.

3.D. Physical Plant Requirements

Physical Plant is responsible for the annual inspection of the fan systems. This includes:

3.D.1.

All hoods must be shut down before going onto the roof to perform the preventative maintenance. Prior approval is MANDATORY before the systems are turned off to prevent unsafe conditions to occur in a laboratory. It is the responsibility of the Physical Plant personnel to advise the laboratory workers or building managers whenever a shutdown is required. Upon completion of the work, the Physical Plant personnel will alert laboratory workers or building manager and advise that the system is once again operational.

3.D.2.

Once the fan system is off, the maintenance personnel are to check belts, grease the motor and make any repairs as needed.

Physical Plant is responsible for repairing fume hoods as notified by the Environmental and Occupational Safety Office.
All requests for new fume hoods will be reviewed by WPI's project engineers. Once the design is complete, a copy will be forwarded to the Environmental and Occupational Safety Office for review. The WPI project engineers will also advise the Environmental and Occupational Safety Office when the project is complete so that the hood may be certified for that use.

3.E. Miscellaneous Fume Hood Information

The Environmental and Occupational Safety Office will perform airflow surveys of any fume hood at the request of the user, department head or Plant Services Department.
The Environmental and Occupational Safety Office maintains certification records of all hoods on campus.
The Environmental and Occupational Safety Office will provide special training sessions by request and will respond to any questions regarding proper hood usage on the WPI campus.

4. Laboratory Worker Information and Training

WPI will provide all laboratory workers with information and training concerning the hazardous chemicals in WPI's laboratories. This information and training shall be provided when a laboratory worker is initially assigned to a laboratory where hazardous chemicals are present and also prior to assignments involving new hazardous chemicals and/or new laboratory work procedures. All lab workers should be re-trained annually.

4.A. Laboratory Worker Information

All laboratory workers at WPI shall be informed of the following:

4.A.1.

The content and requirements of the OSHA laboratory standard.

4.A.2.

The content, location, and availability of the WPI chemical hygiene plan. (CHP)

4.A.3.

The PEL's, action levels and other recommended exposure limits for hazardous chemicals used in WPI laboratories.

4.A.4.

The signs and symptoms associated with exposure to the hazardous chemicals used in the laboratory.

4.A.5.

The location and availability of MSDS's and other reference materials on the hazards, safe handling, storage and disposal of hazardous chemicals found in the laboratory.

The OSHA Laboratory Standard and the WPI Chemical Hygiene Plan are located in the following areas:

Dave Messier - Environmental and Occupational Safety Office - Olin 030 - x5216

Michael Carney - Human Resources Director
Human Resources Department- Stratton Hall- x 5470

It is available during normal working hours, 7:00 AM to 5:00 PM. Access at all other times is available through the Campus Police Department, x 5443.

David Messier, is responsible for the management and availability of all MSDS's and other reference materials. He can be contacted at the previously listed location. The availability of this material is also the same as previously stated.

4.B. Laboratory Worker Training

All laboratory workers at WPI shall receive training in the following areas:

4.B.1.

The methods and observations that may be used to detect the presence or release of a hazardous chemical.

4.B.2.

The hazards associated with the chemicals used in WPI laboratories.

4.B.3.

The measures laboratory workers can use to protect themselves from these hazards, including specific procedures such as appropriate work practices, personal protective equipment to be used and emergency procedures.

4.B.4.

The details of the WPI Chemical Hygiene Plan.

5. Laboratory Operations or Procedures That Require Prior Approval

All laboratory workers must obtain prior approval to proceed with a laboratory task from their immediate supervisor or his or her designee whenever:

5.A.

A new laboratory procedure or test is about to be carried out.

5.B.

It is likely that toxic limit concentrations could be exceeded or that other harm is likely.

5.C.

There is a change in a procedure or test, which may include:

5.C.1.

A 10% or greater increase or decrease in the amount of one or more chemicals used.

5.C.2.

A substitution or deletion of any of the chemicals used in the procedure.

5.C.3.

Any change in other conditions under which the procedure is to be conducted.

5.D.

There is a failure of any of the equipment used in the process, especially of safeguards such as fume hoods or clamped apparatus.

5.E.

There are unexpected results.

5.F.

Members of the laboratory staff become ill, suspect that they or others have been exposed, or otherwise suspect a failure of any safeguards.

5.G.

Whenever a student, faculty or staff member introduces a new hazardous material into the laboratory, prior approval must be granted by the Environmental and Occupational Safety Manager before the material is permitted on campus. This includes all materials with biological, chemical and radiological hazards.

The occurrence of any of these conditions should result in work stoppage and immediate investigation by the laboratory supervisor. The results of the investigation should be reported immediately to the Chemical Hygiene Officer who must decide whether to continue the investigation, institute any additional corrective actions beyond those of the laboratory supervisor, or allow work to continue.

6. Exposure Assessments, Medical Consultations, and Examinations

6.A.

There may be times when laboratory workers or supervisors suspect that someone has been exposed to a hazardous chemical to a degree and in a manner that might have caused harm to the victim. If the circumstances suggest a reasonable suspicion of exposure, the victim is entitled to a medical consultation, and if determined in the consultation, also to a medical examination at no cost, with no loss of work day time attributed to the victim.

6.A.1. Criteria for Reasonable Suspicion of Exposure

It is the policy of WPI to promptly investigate all work-related incidents in which there is even a remote possibility of laboratory worker overexposure to a toxic substance.
Events or circumstances that might reasonably constitute overexposure include:
A hazardous chemical leak, spill, or other uncontrolled release.
A laboratory worker has direct skin or eye contact with a hazardous chemical.
A laboratory worker manifests symptoms such as headache, rash, nausea, coughing, tearing, irritation or redness of the eyes, irritation of nose or throat, dizziness, loss of motor dexterity, etc. and:
- Some or all of the symptoms disappear when the person is taken away from the exposure area and breathes fresh air, and the symptoms reappear soon after the employee returns to work with the same hazardous chemicals.
- Two or more persons in the same laboratory have the same complaints.

6.B. Exposure Assessment

In cases of emergency, exposure assessments are conducted after the victim has been treated.

Note: It is not the purpose of an exposure assessment to determine that a failure on the part of the victim, or others, to follow proper procedures was the cause of an exposure. The purpose of an exposure assessment is to determine that there was or was not an exposure that might have caused harm to one or more laboratory workers, and if so, to identify the hazardous chemical or chemicals involved. Another purpose of an exposure assessment will include a risk assessment in order to insure that a failure will not occur again, and thereby prevent future exposures.

6.C.1.

Unless circumstances suggest other or additional steps, these actions constitute an exposure assessment:

Interview the complainant and also the victim if not the same person.
List the essential information about the circumstances of the complaint, including:
- The chemical under suspicion.
- Other chemicals used by the victim.
- All chemicals being used by others in the immediate area.
- Other chemicals stored in that area.
- Symptoms exhibited or claimed by the victim.
- How these symptoms compare to symptoms stated in the MSDS for each of the identified chemicals.
- Were control measures, such as personal protective equipment and fume hoods, used properly?
- Were any air sampling or other monitoring devices in place? If so, were the measurements obtained from these devices consistent with other information?
- Monitor or sample the air in the area for suspect chemicals.
- Determine whether the victim's symptom compare to the symptoms described in the MSDS or other reference material.
- Determine whether the present control measures and safety procedures are adequate.
- Within 15 working days of receipt of the results of any monitoring, laboratory workers will be notified of those results.

6.D. Medical Examination and Consultation

The purpose of a medical consultation is to determine whether a medical examination is warranted. When, from the results of an exposure assessment, it is suspected or known that a laboratory worker was overexposed to a hazardous chemical or chemicals, the laboratory worker should obtain medical consultation from or under the direct supervision of a licensed physician.

When warranted, laboratory workers should receive a medical examination from or under the direct supervision of a licensed physician who is experienced in treating the victims of chemical overexposure. The medical professional should also be knowledgeable about which tests or procedures are appropriate to determine if there has been an overexposure.

These provisions apply to medical consultations and examinations:

6.D.1.

WPI will provide all laboratory workers who work with hazardous chemicals an opportunity to receive medical consultation and examination when:

The laboratory worker develops signs or symptoms associated with a hazardous chemical to which the worker may have been exposed.
Monitoring, routine or otherwise, suggests that there could have been an exposure above the action level, for a chemical for which a substance-specific standard has been established.
There is a spill, leak or other uncontrolled release of a hazardous chemical.

6.D.2.

The physician is to be provided with:

The identity of the hazardous chemical or chemicals to which the laboratory worker might have been exposed.
The exposure conditions, if any.

6.D.3.

The physician will furnish the employer in written form:

Recommendations for follow-up, if determined to be pertinent.
A record of the results of the consultation and, if applicable, of the examination and any tests that were conducted.
Conclusions concerning any other medical condition noted that could put the laboratory worker at increased risk.
A statement that the laboratory worker has been informed both of the results of the consultation and examination, and of any medical condition that may require further examination or treatment.

6.D.4.

These written statements and records should not reveal specific findings that are not related to an occupational exposure.

6.E. Documentation

All memos, notes and reports related to a complaint of actual or possible exposure to hazardous chemicals are to be maintained as part of the record, for the duration of the workers employment, plus 30 years thereafter.

6.F. Notification

WPI laboratory workers shall be notified of the result of any medical consultation or examination with regard to any medical condition that exists or might exist as a result of overexposure to a hazardous chemical.

7. Designation of Responsible WPI Personnel, Including the Chemical Hygiene Officer

7.A. Responsibilities of the individual laboratory worker:

7.A.1.

Each person working with or around chemicals is responsible for remaining aware of the hazards of those materials and handling those materials in a safe manner.

7.A.2.

Each person is responsible for knowing how to store, use, and dispose of hazardous chemicals based on the hazards of the materials they are working with.

7.B. Responsibilities of the Laboratory Supervisor (faculty, staff, etc.)

7.B.1.

Each laboratory supervisor has the responsibility of giving all the necessary safety instructions to his or her workers prior to the beginning of any laboratory work involving hazardous chemicals.

7.B.2.

Each laboratory supervisor has the responsibility of seeing that laboratory workers carry out their individual safety responsibilities.

7.B.3.

Each laboratory supervisor will be familiar with the WPI Chemical Hygiene Plan.

7.C. Responsibilities of the WPI Chemical Hygiene Officer

7.C.1.

The Chemical Hygiene Officer (CHO) is an individual qualified by training and experience to provide technical guidance in the development and implementation of the Chemical Hygiene Plan (CHP).

7.C.2.

The CHO is responsible to set forth work practices, procedures, personal protective equipment, and other equipment that will protect the health and safety of laboratory workers.

The designated Chemical Hygiene Officer at WPI is the Environmental and Occupational Safety Office Manager, David Messier. This position reports to the Director of Physical Plant, Mr. John E. Miller.

8. Procedures for Carcinogens, Reproductive Toxins, Substances That Have A High Degree of Acute Toxicity, and Chemicals of Unknown Toxicity

The following procedures in this section will apply when performing laboratory work with greater than 10 mg. of any carcinogen, reproductive toxin, substance that has a high degree of acute toxicity, or a chemical whose toxic properties are unknown.

8.A.

The following definitions apply:

8.A.1.

Select carcinogen: Any substance defined as such in 29CFR1910.1450 and any other substance described as such in the applicable MSDS.

8.A.2.

Reproductive toxin: Any substance described as such in the applicable MSDS.

8.A.3.

Substance with a high degree of acute toxicity: Any substance for which the LD50 data described in the applicable MSDS causes the substance to be classified as a "highly toxic chemical" as defined in ANSI Z129.1.

8.A.4.

Chemicals whose toxic properties are unknown: A chemical for which there is no known statistically significant study conducted in accordance with established scientific principles that establishes its toxicity.

8.A.5.

For the purpose of this CHP, chemicals in these four categories, 8.A.1. to 8.A.4., will be called "particularly hazardous chemicals".

8.A.6.

Designated Area: A hood, glove box, portion of the laboratory, or an entire laboratory room designated as the only area where work with quantities of particularly hazardous chemicals in excess of the specified limit shall be conducted.

8.B.

Designated areas shall be posted and their boundaries clearly marked. Only those persons trained to work with particularly hazard chemicals will work with those chemicals in a designated area. All such persons will:

8.B.1.

Use the smallest amount of the chemical that is consistent with the requirements of the work that is to be done.

8.B.2.

Store particularly hazardous chemicals only in the designated area.

8.B.3.

Decontaminate a designated area when work has been completed.

8.B.4.

Prepare wastes from work with particularly hazardous chemicals for waste disposal in accordance with any specific disposal procedures consistent with Federal and State regulations, and the WPI Hazardous Waste Policy.

8.C.

Laboratory workers using particularly hazardous chemicals shall take extra precautions in maintaining good personal hygiene. In addition to the hygiene practices in Section 1.B., workers should not wear any personal items, such as jewelry which might be difficult or impossible to decontaminate.

When possible, disposable clothing should be used.
Gloves and long sleeves should be used at all times to prevent skin contact with particularly hazardous chemicals.

As stated in the beginning, this Chemical Hygiene Plan is generic for all WPI laboratories. It is to be used as a starting point of lab safety information. It is the responsibility of the laboratory supervisor to add specific safety information for his/her laboratory operations and experiments which are not covered by this plan.

Maintained by webmaster@wpi.edu
Last modified: Jun 29, 2004, 15:03 EDT